3.0T Performance Software All Stages | Eurodyne B8/8.5 Audi S4

Eurodyne B8/8.5 Audi S4 | 3.0T Performance Software All Stages

$699.00

Part# Eurodyne-Power-Tap

In Stock

QTY:

On Backorder
Notify Me when Back in stock

Earn Rewards! +3495 Points

Select Your Car to Verify Fitment

Eurodyne now offers Stage 1 & 2 software for the 3.0T S4!

Stage 1 - 91 Octane

Performance Software Precisely Engineered to Run on a Completely Stock Car.
428 HP @ 7200RPM
370 TQ @ 4100 RPM

Stage 1 - 93 Octane

Performance Software Precisely Engineered to Run on a Completely Stock Car.
441 HP @ 7200RPM
375 TQ @ 4500 RPM

Stage 2 - 91 Octane (must have 57.02mm pulley)

Designed for use with 57.02mm pulley.
437 HP @ 7200RPM
386 TQ @ 4500 RPM

Stage 2 - 93 Octane (must have 57.02mm pulley)

Designed for use with 57.02mm pulley.
455 HP @ 7200RPM
395 TQ @ 4500 RPM

Installation

Flashed directly through the (OBDII) Diagnostic port of your vehicle (~30 minutes).

Powertap Air Flash Tool

The Powertap Air Flash Tool allows you to program your own vehicle right in your own garage either plugging in using your computer or wirelessly using your IOS Phone (Currently does not support Android)

Features for all Stages

Engineered with Strict Industry Standards
Extensively Tested Under Various Driving Conditions
Factory Safety Limiters Retained
Greatest Power and Torque Gains in the Industry, Guaranteed!
Optimized Responsiveness and Drivability
Optimized Smoothness and Driving Comfort
Power Delivery Perfectly Optimized Throughout the Power Band
Improved Fuel Efficiency
Speed Governor Removed
Lower End Hesitation (Lag) Removed

Stage 1 (91 Octane)

Stage 1 (93 Octane)

Stage 2 57mm Pulley (93 Octane)

Stage 2 57mm Pulley (93 Octane)

Stage 2 57mm SC - 189 Crank Pulley (93 Octane)

**LOCAL CUSTOMERS contact us for details on having your car tuned at our store. Call or Text 813-444-7021

NOTE: This software is also available to be installed locally at the UroTuning facility in Tampa Florida . Call us to setup an appointment at 813-444-7021

Upgrade Policy: Once you have purchased the reflash, you can switch between available file versions including stock software for no additional charge from Eurodyne. The included flash software will allow you to perform data-logging and supports some diagnostic functions such as clearing fault codes and the ability to scan and recode other modules in the vehicle.

Powertap Air Flash Cable

This package will allow anyone with a Windows PC or tablet with USB port, and an internet connection to flash their ecu with our stage 1 or stage 2 software.

With the included Powertap interface and

Eurodyne flash software you can switch between available stages and even flash the ecu back to stock if necessary.

Also included is diagnostic software that will allow you to check and clear fault codes, and datalog engine parameters.

Certain models support recoding of some modules as well. See the applicable stage 1 and stage 2 software product pages for details on power increases for your model.

We support port flashing for all models now, no ecu removal is required.

Screenshots for datalogging vary depending on the model. Due to the large number of different ecu codes, there may be a delay in adding support for new or rare software versions.

⚠️CALIFORNIA WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Fitments

Reviews / Q&A

Shipping & Returns